- Il n'y a plus d'articles dans votre panier
- Livraison
- Total 0,0 CHF
- Pièces pour serveur, notebook & imprimante
- Notebooks & pièces détachées
- Serveurs & notebooks
- Imprimantes & pièces détachées
- Pièces smartphones & tablettes
- Câbles
- Stockage de données
- Logiciels & licences
- Châssis & composants
- Santé & hygiène
- Autre
- Solutions ProAV
- Moniteurs & écrans
- Solutions d’affichage LED
- Vidéoprojecteurs
- Equipements de conférence
- Câbles
- Gestion des signaux
- Logiciels & licences
- Supports & meubles
- Audio
- Accessoires
- Autre
- Surveillance & sécurité
- Caméras
- Enregistreurs & serveurs
- Contrôle d'accès
- Infrastructure réseau
- Fire
- Câbles
- Systèmes d'alarme
- Logiciels & licences
- Audio
- Périphériques
- Moniteurs & écrans
- Réseau
- POS & Auto-ID
- POS & périphériques
- Lecteurs codes-barres
- Impression
- Imprimantes media
- Câbles
- Mobilité
- Software & Licenses
- Accessoires
- Autre
- Electronique grand public
- Image & son
- Mobilité
- Sacs pour ordinateur portable
- Accessoires ordinateur
- Câbles
- Smart Home
- Home & Leisure
- Accessoires automobile
- Gaming & gadgets
- Photo & Accessoires
- Tools
- Autre
- Câbles
- Câbles Vidéo
- Câbles audio
- Câbles Data
- Câbles réseau
- Câbles d’alimentation
- Câbles signal
- Gestion des câbles
36,9 CHF
TTC
34,1 CHF
HT
En stock
Référence: 110900
Marque: Brady
M21-500-430
Polyester tape for M211 M210 BMP21-PLUS BMP21-LAB BMP21 Polyester
98,2 CHF
TTC
90,8 CHF
HT
En stock
Description
For fixed installation, with Molex adapter system. 2A charger. The cables are to be connected inside the dashboard, this gives a discreet, neat installation without cables hanging over the interior.
With the Molex adapter system you can get power for a Bluetooth GPS receiver etc. (The device does not support datatransfer.)
12/24 Volt. The product is E-approved. Connect the power cable with a 2 A fuse. 2 A charger. Professional installation recommended. The holder is attached onto a tilt swivel and can be adjusted in order to avoid light reflection. Attach onto a ProClip Mounting Platform. Please read all of the instructions and look at the pictures before attaching the holder. Important Note: The charger unit is fused internally with 2 A automotive re-settable thermal fuse, but if an external fuse is to be installed then connect a 2 A fuse holder and fuse inline with the Red wire close to the power source. Route the cable from the holder into the vehicle dashboard and secure the charger unit in place with the adhesive tape provided. Ensure the charger unit is securely mounted behind the dashboard in a well ventilated area that does not get hot! Note: If you are connecting a GPS/Data device to the holder please ensure the charger unit is located in a position within easy reach of any GPS or charging adapters.
Route the power cable from the charger unit to the power supply source in the vehicle and connect as follows: 1. Connect the White wire to a Negative Ground connection of the vehicle or the vehicle chassis. 2. Connect the Red wire to a 12/24 Volt power supply in the vehicle that is controlled by the ignition switch of the vehicle.
Installation of the holder: 1. Loosen the screw in the center of the holder so you can remove the tilt swivel attaching plate on the back. 2. Place the attaching plate on desired position. Screw the attaching plate into place with the enclosed screws. 3. Place the holder over the attaching plate so the tilt swivel fits. Screw the holder onto the attaching plate. 4. The holder is in place.
With the Molex adapter system you can get power for a Bluetooth GPS receiver etc. (The device does not support datatransfer.)
12/24 Volt. The product is E-approved. Connect the power cable with a 2 A fuse. 2 A charger. Professional installation recommended. The holder is attached onto a tilt swivel and can be adjusted in order to avoid light reflection. Attach onto a ProClip Mounting Platform. Please read all of the instructions and look at the pictures before attaching the holder. Important Note: The charger unit is fused internally with 2 A automotive re-settable thermal fuse, but if an external fuse is to be installed then connect a 2 A fuse holder and fuse inline with the Red wire close to the power source. Route the cable from the holder into the vehicle dashboard and secure the charger unit in place with the adhesive tape provided. Ensure the charger unit is securely mounted behind the dashboard in a well ventilated area that does not get hot! Note: If you are connecting a GPS/Data device to the holder please ensure the charger unit is located in a position within easy reach of any GPS or charging adapters.
Route the power cable from the charger unit to the power supply source in the vehicle and connect as follows: 1. Connect the White wire to a Negative Ground connection of the vehicle or the vehicle chassis. 2. Connect the Red wire to a 12/24 Volt power supply in the vehicle that is controlled by the ignition switch of the vehicle.
Installation of the holder: 1. Loosen the screw in the center of the holder so you can remove the tilt swivel attaching plate on the back. 2. Place the attaching plate on desired position. Screw the attaching plate into place with the enclosed screws. 3. Place the holder over the attaching plate so the tilt swivel fits. Screw the holder onto the attaching plate. 4. The holder is in place.
Spécifications
Vendor information
| Brand Name | Brodit |
| Homepage | http://www.brodit.se/product.html?locale=se&id=971742 |
| Warranty | 1 |
Détails du produit
2026-05-01
Neuf
Fiche technique
- Homepage
- http://www.brodit.se/product.html?locale=se&id=971742
- Brand Name
- Brodit
- Warranty
- 1
Références spécifiques
- EAN13
- 7320289717424
- MPN
- 971742
16 autres produits dans la même catégorie :
Marque: RAM Mounts
RAM-B-407U
RAM Tough Wedge, B-size Tough-Wedge Base with Ball, Tablet/UMPC, Car, Black
70,6 CHF
TTC
65,3 CHF
HT
Sera commandé pour vous
73,2 CHF
TTC
67,7 CHF
HT
Sera commandé pour vous
158,7 CHF
TTC
146,8 CHF
HT
Sera commandé pour vous
For fixed installation, with Molex adapter system. 2A charger.