- Non ci sono più articoli nel tuo carrello
- Spedizione
- Totale 0,0 CHF
- Parti per Server, Computer e Stampanti
- Notebook e parti di ricambio
- Server & Computer
- Stampanti e parti di ricambio
- Ricambi telefono cellulare
- Cavi
- Data Storage
- Software e licenze
- Componenti Chassis
- Salute e Sicurezza
- Autre
- Soluzioni ProAV
- Display e monitor
- LED Display Soluzioni
- Proiettori
- Attrezzature per conferenze
- Cavi
- Gestione del segnale
- Software e licenze
- Supporti e mobili
- Audio
- Accessori
- Autre
- Sorveglianza e Sicurezza
- Telecamere
- Registratori e server
- Controllo Accessi
- Infrastruttura
- Fire
- Cavi
- Sistemi di allarme
- Software e licenze
- Audio
- Periferiche
- Monitor e Display
- Network
- POS e Auto-ID
- Consumer Electronics
- Sound & Vision
- Accessori per cellulari e tablet
- Borse per notebook
- Accessori per computer
- Cavi
- Smart Home
- Home & Leisure
- Settore automobilistico
- Giochi e gadget
- Foto e accessori
- Tools
- Autre
- Cavi
- Cavi Video
- Cavi audio
- Cavi Dati
- Cavi di rete
- Cavi di alimentazione
- Cavi di segnale
- Cable Management
Riferimento: ST3450857SS
Marca: Seagate
ST3450857SS _ RFB
Seagate Cheetah 450GB 3.5, 450 GB, 15000 Giri/min, 16 MB, 3.5", SAS
238,9 CHF
tasse incl.
221,0 CHF
tasse escl.
In magazzino
514,3 CHF
tasse incl.
475,8 CHF
tasse escl.
In magazzino
143,3 CHF
tasse incl.
132,6 CHF
tasse escl.
In magazzino
Descrizione
For fixed installation, with Molex adapter system. 2A charger. The cables are to be connected inside the dashboard, this gives a discreet, neat installation without cables hanging over the interior.
With the Molex adapter system you can get power for a Bluetooth GPS receiver etc. (The device does not support datatransfer.)
12/24 Volt. The product is E-approved. Connect the power cable with a 2 A fuse. 2 A charger. Professional installation recommended. The holder is attached onto a tilt swivel and can be adjusted in order to avoid light reflection. Attach onto a ProClip Mounting Platform. Please read all of the instructions and look at the pictures before attaching the holder. Important Note: The charger unit is fused internally with 2 A automotive re-settable thermal fuse, but if an external fuse is to be installed then connect a 2 A fuse holder and fuse inline with the Red wire close to the power source. Route the cable from the holder into the vehicle dashboard and secure the charger unit in place with the adhesive tape provided. Ensure the charger unit is securely mounted behind the dashboard in a well ventilated area that does not get hot! Note: If you are connecting a GPS/Data device to the holder please ensure the charger unit is located in a position within easy reach of any GPS or charging adapters.
Route the power cable from the charger unit to the power supply source in the vehicle and connect as follows: 1. Connect the White wire to a Negative Ground connection of the vehicle or the vehicle chassis. 2. Connect the Red wire to a 12/24 Volt power supply in the vehicle that is controlled by the ignition switch of the vehicle.
Installation of the holder: 1. Loosen the screw in the center of the holder so you can remove the tilt swivel attaching plate on the back. 2. Place the attaching plate on desired position. Screw the attaching plate into place with the enclosed screws. 3. Place the holder over the attaching plate so the tilt swivel fits. Screw the holder onto the attaching plate. 4. The holder is in place.
With the Molex adapter system you can get power for a Bluetooth GPS receiver etc. (The device does not support datatransfer.)
12/24 Volt. The product is E-approved. Connect the power cable with a 2 A fuse. 2 A charger. Professional installation recommended. The holder is attached onto a tilt swivel and can be adjusted in order to avoid light reflection. Attach onto a ProClip Mounting Platform. Please read all of the instructions and look at the pictures before attaching the holder. Important Note: The charger unit is fused internally with 2 A automotive re-settable thermal fuse, but if an external fuse is to be installed then connect a 2 A fuse holder and fuse inline with the Red wire close to the power source. Route the cable from the holder into the vehicle dashboard and secure the charger unit in place with the adhesive tape provided. Ensure the charger unit is securely mounted behind the dashboard in a well ventilated area that does not get hot! Note: If you are connecting a GPS/Data device to the holder please ensure the charger unit is located in a position within easy reach of any GPS or charging adapters.
Route the power cable from the charger unit to the power supply source in the vehicle and connect as follows: 1. Connect the White wire to a Negative Ground connection of the vehicle or the vehicle chassis. 2. Connect the Red wire to a 12/24 Volt power supply in the vehicle that is controlled by the ignition switch of the vehicle.
Installation of the holder: 1. Loosen the screw in the center of the holder so you can remove the tilt swivel attaching plate on the back. 2. Place the attaching plate on desired position. Screw the attaching plate into place with the enclosed screws. 3. Place the holder over the attaching plate so the tilt swivel fits. Screw the holder onto the attaching plate. 4. The holder is in place.
Specifiche
Vendor information
| Brand Name | Brodit |
| Homepage | http://www.brodit.se/product.html?locale=se&id=971742 |
| Warranty | 1 |
Dettagli del prodotto
2026-06-15
Nuovo
Scheda tecnica
- Homepage
- http://www.brodit.se/product.html?locale=se&id=971742
- Brand Name
- Brodit
- Warranty
- 1
Riferimenti Specifici
- ean13
- 7320289717424
- MPN
- 971742
16 altri prodotti della stessa categoria:
56,2 CHF
tasse incl.
52,0 CHF
tasse escl.
Verrà ordinato per te
109,5 CHF
tasse incl.
101,3 CHF
tasse escl.
Verrà ordinato per te
49,7 CHF
tasse incl.
46,0 CHF
tasse escl.
Verrà ordinato per te
59,5 CHF
tasse incl.
55,0 CHF
tasse escl.
Verrà ordinato per te
For fixed installation, with Molex adapter system. 2A charger.